ChickenCoopPlanner.com

Chicken run plans for your flock

Pick the flock and the options. Every cut, board and roll of hardware cloth is recalculated.

Free to designPDF plan · $9.99 one-time

20 hens
140
Breed size
Height
Top
Roofing
Predator apron
Hardware cloth mesh
WoodNatural pine
AssemblyFully assembled

View

Switch layers off to see the frame inside.

One-time payment · No subscription

Get the build plan

$9.99

Designing is free. The PDF for this exact run is a one-time $9.99.

  • Cut list and cutting diagrams
  • Every wall drawn with each screw
  • Step-by-step illustrated assembly
  • No account needed

What's in the chicken run plan

The plan is a PDF made for your flock and the options you pick above: the height, the top, the apron and the mesh. The run is sized for your hens first, and then every post, rail and roll of hardware cloth is worked out. A run for 8 hens comes to 18 different parts, 42 pieces in all, 3 of them with an angled cut, and 10 assembly steps.

  • A space check: the run area your flock needs against what the plan gives them.
  • A shopping list grouped by store aisle (lumber, hardware cloth, roofing, fasteners, hardware & finish), with every board length and an estimated cost.
  • A cut list with a label for every part, and board-by-board cutting diagrams that allow for the saw kerf.
  • The post layout, with how deep to set each post and how to square the corners.
  • The door, framed and hung, with a two-step raccoon-proof latch.
  • The hardware cloth and predator apron layout, roll by roll.
  • Step-by-step assembly with an illustration for every step, and a predator-proofing checklist.

It is a free-standing run. If you are building a coop as well, the walk-in coop plan comes with an attached run sized for the same flock. See a sample plan first.

How big should a chicken run be?

A standard hen needs 10 sq ft of run, a bantam 5 and a large breed 12. The planner takes the smallest run that gives the flock that area, for 1 to 40 hens. Lengths go in 2 ft steps, a run is never more than four times as long as it is wide, and a roofed run stays narrow enough for one rafter to span. Where two sizes are close, the cheaper build wins. The table shows the run it draws for standard hens.

HensRun area neededRunRun area givenMaterials (est.)
8 chickens80 sq ft10 × 8 ft80 sq ftabout $1,100
10 chickens100 sq ft10 × 10 ft100 sq ftabout $1,200
12 chickens120 sq ft12 × 10 ft120 sq ftabout $1,290
15 chickens150 sq ft16 × 10 ft160 sq ftabout $1,460
20 chickens200 sq ft20 × 10 ft200 sq ftabout $1,690
25 chickens250 sq ft32 × 8 ft256 sq ftabout $2,070
30 chickens300 sq ft30 × 10 ft300 sq ftabout $2,210
40 chickens400 sq ft40 × 10 ft400 sq ftabout $2,690

Each flock page has the coop, the run and the breed and climate tables for that number of hens. To size the coop as well, use the chicken coop size calculator.

Materials and cost

The materials for a 6 ft run with a half roof come to about $1,100 for 8 hens and about $2,690 for 40 hens. The starter plan, the 4-hen run the configurator opens with, needs about $800. The estimates use rough US big-box prices.

For an 8-hen run at about $1,100, this is what the options change:

  • Top: a hardware cloth top is −$220, a full solid roof +$30.
  • Height: a 4 ft run is −$180 against 6 ft.
  • Mesh: 1/4 in hardware cloth instead of 1/2 in is +$170, and keeps mice and snakes out too.
  • Apron: the 24 in skirt and the 12 in buried apron come to the same, so choose by your ground, not the price.

Prices vary by store, region and season, so use them to compare designs, not as a quote. The plan itself is $9.99, one time.

Skill level and tools

A run is the easiest build here: posts, rails and hardware cloth, with no walls or floor. The posts are set in the ground and the rails screwed between them, so the most important job is getting the corners square and the post tops level; the plan shows how. The 3 angled cuts each have their angle printed.

Tools you will need:

  • A post hole digger or a shovel, and a tamper for the gravel around the posts.
  • A circular saw or miter saw.
  • A drill/driver, with a bit to pre-drill screws near the board ends.
  • Tin snips for the hardware cloth.
  • A tape measure, a speed square, a level and a string line.

The screws are all in the shopping list: 3-1/2" structural screws, 2-1/2" exterior deck screws, 1-1/4" screws for hinges, 1-1/4" screws for latches, 1" screws + 1-1/4" fender washers (hardware cloth).

Chicken run FAQ

How big should a chicken run be?

10 sq ft per standard hen, 5 for bantams and 12 for large breeds. So 8 standard hens need 80 sq ft and 40 need 400 sq ft. The planner picks the smallest run that fits.

Should a chicken run have a roof?

A roof keeps the run dry and stops hawks. The plan offers a hardware cloth top, a half solid roof (the default) or a full solid roof. For 8 hens a cloth top is −$220 and a full roof +$30 against the half roof.

How do I stop predators digging into the run?

With an apron of hardware cloth: either a 24 in skirt laid flat on the ground outside the run, or a 12 in apron buried in a trench. Fasten the cloth with screws and washers, not staples alone, and fit a two-step latch on the door: raccoons can open a simple hook.

How tall should a chicken run be?

The plan builds it 4, 6 or 7 ft tall. 6 ft is the default, so you can walk in to clean it; a 4 ft run is −$180 for 8 hens.

Can I attach the run to my coop?

This plan is a free-standing run with its own door. If you are building a coop too, the walk-in coop plan includes an attached run sized for the same flock.

Is there a free chicken run plan?

Yes, for a limited time. The starter plan, the 4-hen run the configurator opens with, downloads free and in full. Change anything and the plan is made for you at the normal price of $9.99.